nn - en to nn translation catalogue (27 entries)

note: Type: select Choices Note to translators : Please keep your translations of the choices below a 65 columns limit (which means 65 characters in single-byte languages) including the initial path :sl5:
en: ctc: Channel to Channel (CTC) or ESCON connection
nn: ctc: Kanal-til-kanal (CTC) eller ESCON-samband

note: Type: select Choices Note to translators : Please keep your translations of the choices below a 65 columns limit (which means 65 characters in single-byte languages) including the initial path :sl5:
en: qeth: OSA-Express in QDIO mode / HiperSockets
nn: qeth: OSA-Express i QDIO-modus / HiperSockets

note: Type: select Choices Note to translators : Please keep your translations of the choices below a 65 columns limit (which means 65 characters in single-byte languages) including the initial path :sl5:
en: iucv: Inter-User Communication Vehicle - available for VM guests only
nn: iucv: Inter-User Communication Vehicle - berre tilgjengeleg for VM-gjester

note: Type: select Description :sl5:
en: Network device type:
nn: Einingstype for nettverk:

note: Type: select Description :sl5:
en: Please choose the type of your primary network interface that you will need for installing the Debian system (via NFS or HTTP). Only the listed devices are supported.
nn: Vel typen til det primære nettverksgrensesnittet du skal bruke til å installere Debian-systemet med (via NFS eller HTTP). Berre dei opplista nettverkseiningane er støtta.

note: Type: select Description :sl5:
en: CTC read device:
nn: CTC-leseeining:

note: Type: select Description :sl5:
en: The following device numbers might belong to CTC or ESCON connections.
nn: Dei følgjande einingsnummera kan høyre til CTC- eller ESCON-samband.

note: Type: select Description :sl5:
en: CTC write device:
nn: CTC-skriveeining:

note: Type: boolean Description :sl5:
en: Do you accept this configuration?
nn: Godtar du dette oppsettet?

note: Type: boolean Description :sl5:
en: The configured parameters are:
     read channel  = ${device_read}
     write channel = ${device_write}
     protocol      = ${protocol}
nn: Dei oppsette parameterane er:
     lesekanal    = ${device_read}
     skrivekanal  = ${device_write}
     protokoll    = ${protocol}

note: Type: error Description :sl5:
en: No CTC or ESCON connections
nn: Fann ingen CTC- eller ESCON-samband

note: Type: error Description :sl5:
en: Please make sure that you have set them up correctly.
nn: Sjå etter at du har sett dei opp rett.

note: Type: select Description :sl5:
en: Protocol for this connection:
nn: Protokoll for dette sambandet:

note: Type: select Description :sl5:
en: Device:
nn: Eining:

note: Type: select Description :sl5:
en: Please select the OSA-Express QDIO / HiperSockets device.
nn: Vel eining for OSA-Express QDIO / HiperSockets.

note: Type: boolean Description :sl5:
en: The configured parameters are:
     channels = ${device0}, ${device1}, ${device2}
     port     = ${port}
     layer2   = ${layer2}
nn: Parameterane i oppsettet er:
     kanalar  = ${device0}, ${device1}, ${device2}
     port     = ${port}
     lag2     = ${layer2}

note: Type: error Description :sl5:
en: No OSA-Express QDIO cards / HiperSockets
nn: Fann ingen OSA-Express QDIO-kort eller HiperSockets

note: Type: error Description :sl5:
en: No OSA-Express QDIO cards / HiperSockets were detected. If you are running VM please make sure that your card is attached to this guest.
nn: Fann ingen OSA-Express-QDIO-kort eller HiperSockets. Dersom du køyrer VM, pass på at kortet er kopla til denne gjesten.

note: Type: string Description :sl5:
en: Please enter a relative port for this connection.
nn: Oppgje relativ port for dette sambandet.

note: Type: boolean Description :sl5:
en: Use this device in layer2 mode?
nn: Skal denne eininga brukast i lag2-modus?

note: Type: boolean Description :sl5:
en: By default OSA-Express cards use layer3 mode. In that mode LLC headers are removed from incoming IPv4 packets. Using the card in layer2 mode will make it keep the MAC addresses of IPv4 packets.
nn: OSA-Express-kort brukar som standard lag3-modus. Då vert LLC-hovuda fjerna frå innkomande IPv4-pakkar. Om kortet vert sett i lag2-modus, så blir MAC-adressane til IPv4-pakkane verande.

note: Type: boolean Description :sl5:
en: The configured parameter is:
     peer  = ${peer}
nn: Den oppsette parameteren er:
     peer = ${peer}

note: Type: string Description :sl5:
en: VM peer:
nn: VM-node:

note: Type: string Description :sl5:
en: Please enter the name of the VM peer you want to connect to.
nn: Oppgje namnet på den VM-noden du vil kopla deg til.

note: Type: string Description :sl5:
en: If you want to connect to multiple peers, separate the names by colons, e.g.  tcpip:linux1.
nn: Dersom du vil ha samband til fleire nodar, bruk kolon som skiljeteikn, til dømes «tcpip:linux1».

note: Type: string Description :sl5:
en: The standard TCP/IP server name on VM is TCPIP; on VIF it's $TCPIP. Note: IUCV must be enabled in the VM user directory for this driver to work and it must be set up on both ends of the communication.
nn: Standard tenarnamn for TCP/IP på VM er TCPIP, på VIF er det $TCPIP. Merk: IUCV må vere slått på i VM-brukarkatalogen for at denne drivaren skal fungera, og det må vere sett opp i begge endar av sambandet.

note: Type: text Description Main menu item Translators: keep below 55 columns :sl5:
en: Configure the network device
nn: Set opp nettverkseininga
